A motorcycle fairing is a shell placed over the frame of some "motorcycles, especially "racing motorcycles and "sport bikes, with the primary purpose to reduce "air drag. The secondary functions are the protection of the rider from airborne hazards and wind-induced "hypothermia and of the engine components in the case of an accident. A "motorcycle windshield will almost always be integrated into the design of the fairing.
The major benefit of a fairing on "sport touring and "touring motorcycles is a reduction in aerodynamic drag, which allows for reduced fuel consumption and permits higher speeds at lower engine rpm, which in turn increases engine life.
A motorcycle may have a front fairing, a rear fairing, a belly fairing, or any combination of these. Alternatively, a single fairing may partially or fully enclose the entire motorcycle, and may even enclose the rider.
The importance of streamlining was known very early in the 20th century, and some streamlining was seen on racing motorcycles as early as the 1920s. Although motorcycles generally have a much higher "power-to-weight ratio than cars, bikes – and particularly the rider – are much less streamlined and the effects of aerodynamic drag on motorcycles are very significant. Consequently, any reduction in a motorcycle's drag coefficient pays dividends in improved performance.
The term fairing came into use in aircraft "aerodynamics with regard to smoothing airflow over a juncture of components where airflow was disrupted. Early streamlining was often unsuccessful resulting in instability. Handlebar fairings, such as those on Harley-Davidson Tourers, sometimes upset the balance of a motorcycle, inducing wobble.
Originally the fairings were "cowlings put around the front of the bike, increasing its frontal area. Gradually they became an integral part of the design. Modern fairings increase the frontal area at most by 5% compared to a naked machine. Fairings may carry headlights, instruments, and other items. If the fairing is mounted on the frame, placing other equipment on the fairing reduces the weight and rotational "inertia of the "steering assembly, improving the handling.
The "BMW R100RS, produced from 1976 to 1984, was the first mass-market "sport touring motorcycle to be offered with a full fairing as standard, and marked the beginning of wider adoption of fairings on sports and touring types of motorcycles. The integrated design included a development of the frame-mounted tail fairing at the rear of the removable dual seat accessing a storage compartment used on the "BMW R90S from 1973, also being the first example of a factory-fitted head (or nose) fairing.
A single piece, streamlined shell covering the front half of a motorcycle resembling the nose of an aircraft, sometimes referred to as torpedo fairing. It dramatically reduced the frontal drag, but it was banned by "Fédération Internationale de Motocyclisme (FIM) from racing in 1958, because it was thought that the frontal point of wind pressure made them highly unstable even with small amounts of "yaw. Other reasons cited for the ban were to ensure adequate steering range (lock-to-lock) and stability in "crosswinds. FIM regulations forbid streamlining beyond the wheel "spindles and require the rider's arms and legs to be visible from the side. However, "Peter Williams was permitted to give his "1973/74 JPS Norton a "Peel-type fairing incorporating handlebar blisters which helped to reduce the "drag coefficient to 0.39.
This was called so because, in early models, the front wheel "mudguard streamlined with the rising windshield part of the fairing resembled the "dolphin's snout from the side view. Further developments on this design became the norm after dustbin fairings were banned.
Full fairings cover both upper and lower portions of the motorcycle, as distinct from a half fairing, which only has an upper section, and leaves the lower half of the motorcycle exposed. The fairing on a race or sport bike is meant as an aerodynamic aid, so the windscreen is rarely looked through. If the rider is sitting up at speed he will be buffeted by his rapid progress through the air and act as a parachute, slowing the bike, while if the rider lies flat on the tank behind the windscreen he generates much less aerodynamic drag. The high windscreen and handlebar width of a touring fairing protect the upright rider from the worst of this, and the windscreen is functional. Full fairings can also provide protection to the engine and chassis in the event of a crash where the fairings, rather than the engine covers and/or frame, slide on the road.
Half fairings usually feature a windscreen and extend below the handlebars, possibly as far down as the sides of the cylinder block, but generally do not cover the sides of the crankcase or gearbox. Aftermarket kits – 'lowers' – are available to extend some half fairings into full fairings. Due to the popularity of these kits, some motorcycle manufacturers have started to supply their own full fairing conversion kits and even offer their half faired models new with a full factory-fitted kit.
A windscreen and minimal fairing extending around the "headlamp fixed to the "triple clamp. Also called a "café fairing or bikini fairing, it stops well below the level of the rider's head, relying primarily on air deflection to protect the rider's head and chest from the slipstream.
Quarter and half fairings are often paired with a belly pan below the engine for diverting air flow away from under the engine to reduce "aerodynamic lift, as well as cosmetic reasons. Some "track day or racing rules require belly pans to catch leaked fluids.
A tail fairing, sometimes referred to as a tail unit or race tail, is mounted behind the seat and rider. Some also extend to the sides of, and below, the saddle and usually providing a small storage space.
"Kawasaki became the first manufacturer to incorporate a tail fairing on a "mass production motorcycle when tail units were fitted to the 1972 250cc "S1 Mach I, 350cc "S2 Mach II, and 750cc "H2 Mach IV models.
"Acrylonitrile butadiene styrene (ABS) plastic is commonly used in original equipment sport bikes and certain aftermarket fairing manufacturers due to its strong, flexible and light weight properties. The advantage of ABS over other plastics is that it combines the strength and rigidity of acrylonitrile and styrene with the toughness of polybutadiene rubber. The proportions of each property vary based on the targeted result.
There are two common methods of producing an ABS plastic fairing: injection and compression molding.
"Fiberglass is made of woven fibers, and is used as a reinforcing agent for many polymer products. The composite properly known as glass-reinforced plastic (GRP), is normally referred to by the name of its reinforcing material. Fiberglass fairings are commonly used on the race track. In most cases fiberglass is lighter, and more durable than ABS Plastic. Damaged fiberglass can be repaired by applying new layers of woven fiberglass cloth mixed with a polymer such as epoxy over the damaged area, followed by sanding and finishing.