Sound recording and reproduction is an "electrical, "mechanical, electronic, or digital inscription and re-creation of "sound waves, such as spoken voice, singing, "instrumental music, or sound effects. The two main classes of sound recording technology are "analog recording and "digital recording. Prior to the development of sound recording, there were mechanical systems for encoding and reproducing instrumental music, such as wind-up "music boxes and, later, "player pianos.
Acoustic "analog recording is achieved by a "microphone diaphragm that can detect and sense the changes in "atmospheric pressure caused by "acoustic sound waves and record them as a mechanical representation of the sound waves on a medium such as a "phonograph record (in which a stylus cuts grooves on a record). In "magnetic tape recording, the sound waves vibrate the microphone diaphragm and are converted into a varying "electric current, which is then converted to a varying "magnetic field by an "electromagnet, which makes a representation of the sound as magnetized areas on a plastic tape with a magnetic coating on it. Analog sound reproduction is the reverse process, with a bigger "loudspeaker diaphragm causing changes to atmospheric pressure to form acoustic sound waves. "Oscillations may also be recorded directly from devices such as an "electric guitar pickup or a "synthesizer, without the use of acoustics in the recording process, other than the need for musicians to hear how well they are playing during "recording sessions via "headphones.
"Digital recording and reproduction converts the analog sound signal picked up by the microphone to a "digital form by the process of "digitization. This lets the audio data be stored and "transmitted by a wider variety of media. Digital recording stores audio as a series of "binary numbers (zeros and ones) representing samples of the "amplitude of the "audio signal at equal time intervals, at a "sample rate high enough to convey all sounds capable of being "heard. Digital recordings are considered higher quality than analog recordings not necessarily because they have "higher fidelity (wider "frequency response or "dynamic range), but because the digital format can prevent much loss of quality found in analog recording due to noise and "electromagnetic interference in playback and mechanical deterioration or damage to the "storage medium. Whereas successive copies of an analog recording tend to degrade in quality, as more noise is added, a digital audio recording can be reproduced endlessly with no degradation in sound quality. A "digital audio signal must be reconverted to analog form during playback before it is "amplified and connected to a "loudspeaker to produce sound.
Long before "sound was first recorded, music was recorded—first by written "music notation, then also by mechanical devices (e.g., wind-up "music boxes, in which a mechanism turns a spindle, which plucks metal tines, thus producing a "melody). Automatic music reproduction traces back as far as the 9th century, when the "Banū Mūsā brothers invented the earliest known "mechanical musical instrument, in this case, a "hydropowered (water-powered) "organ that played interchangeable cylinders. According to Charles B. Fowler, this "...cylinder with raised pins on the surface remained the basic device to produce and reproduce music mechanically until the second half of the nineteenth century."["unreliable source?] The Banu Musa brothers also invented an "automatic "flute player, which appears to have been the first "programmable machine. According to Fowler, the automata were a "robot "band that performed "...more than fifty facial and body actions during each musical selection."
In the 14th century, "Flanders introduced a mechanical bell-ringer controlled by a rotating cylinder. Similar designs appeared in "barrel organs (15th century), "musical clocks (1598), "barrel pianos (1805), and "musical boxes (ca.1800). A music box is an automatic "musical instrument that produces sounds by the use of a set of "pins placed on a revolving "cylinder or disc so as to pluck the tuned teeth (or "lamellae) of a steel "comb. They were developed from musical "snuff boxes of the 18th century and called carillons à musique. Some of the more complex boxes also have a tiny "drum and/or "bells, in addition to the metal comb.
The "fairground organ, developed in 1892, used a system of accordion-folded punched cardboard books. The "player piano, first demonstrated in 1876, used a punched paper scroll that could store a long piece of music. The most sophisticated of the piano rolls were "hand-played", meaning that the roll represented the actual performance of an individual, not just a transcription of the sheet music. This technology to record a live performance onto a piano roll was not developed until 1904. Piano rolls were in continuous mass production from 1896 to 2008. A 1908 "U.S. Supreme Court copyright case noted that, in 1902 alone, there were between 70,000 and 75,000 player pianos manufactured, and between 1,000,000 and 1,500,000 piano rolls produced. The use of piano rolls began to decline in the 1920s although one type is still being made today.
Problems playing this file? See "media help.
The first device that could record actual "sounds as they passed through the air (but could not play them back—the purpose was only visual study) was the "phonautograph, patented in 1857 by Parisian inventor "Édouard-Léon Scott de Martinville. The earliest known recordings of the human voice are phonautograph recordings, called "phonautograms", made in 1857. They consist of sheets of paper with sound-wave-modulated white lines created by a vibrating stylus that cut through a coating of soot as the paper was passed under it. An 1860 phonautogram of "Au Clair de la Lune, a French folk song, was played back as sound for the first time in 2008 by scanning it and using software to convert the undulating line, which graphically encoded the sound, into a corresponding digital audio file.
Problems playing this file? See "media help.
On April 30, 1877, French poet, humorous writer and inventor "Charles Cros submitted a sealed envelope containing a letter to the "Academy of Sciences in Paris fully explaining his proposed method, called the paleophone. Though no trace of a working paleophone was ever found, Cros is remembered as the earliest inventor of a sound recording and reproduction machine. The first practical sound recording and reproduction device was the mechanical "phonograph cylinder, invented by "Thomas Edison in 1877 and patented in 1878. The invention soon spread across the globe and over the next two decades the commercial recording, distribution, and sale of sound recordings became a growing new international industry, with the most popular titles selling millions of units by the early 1900s. The development of mass-production techniques enabled cylinder recordings to become a major new consumer item in industrial countries and the cylinder was the main consumer format from the late 1880s until around 1910.
The next major technical development was the invention of the "gramophone disc, generally credited to "Emile Berliner and commercially introduced in the United States in 1889, though others had demonstrated similar disk apparatus earlier, most notably Alexander Graham Bell in 1881. Discs were easier to manufacture, transport and store, and they had the additional benefit of being louder (marginally) than cylinders, which by necessity, were single-sided. Sales of the "gramophone record overtook the cylinder ca. 1910, and by the end of World War I the disc had become the dominant commercial recording format. Edison, who was the main producer of cylinders, created the "Edison Disc Record in an attempt to regain his market. In various permutations, the audio disc format became the primary medium for consumer sound recordings until the end of the 20th century, and the double-sided 78 rpm shellac disc was the standard consumer music format from the early 1910s to the late 1950s.
Although there was no universally accepted speed, and various companies offered discs that played at several different speeds, the major recording companies eventually settled on a de facto industry standard of nominally 78 revolutions per minute, though the actual speed differed between America and the rest of the world. The specified speed was 78.26 rpm in America and 77.92 rpm throughout the rest of the world. The difference in speeds was due to the difference in the cycle frequencies of the AC electricity that powered the "stroboscopes used to calibrate recording lathes and turntables. The nominal speed of the disc format gave rise to its common nickname, the "seventy-eight" (though not until other speeds had become available). Discs were made of shellac or similar brittle plastic-like materials, played with needles made from a variety of materials including mild steel, thorn, and even sapphire. Discs had a distinctly limited playing life that varied depending on how they were produced.
Earlier, purely acoustic methods of recording had limited sensitivity and frequency range. Mid-frequency range notes could be recorded, but very low and very high frequencies could not. Instruments such as the violin were difficult to transfer to disc. One technique to deal with this involved using a Stroh violin to which was fitted a conical horn connected to a diaphragm that vibrated due to the violin bridge. The horn was no longer needed once electrical recording was developed.
The long-playing 33 1⁄3 rpm microgroove "vinyl record, or ""LP", was developed at Columbia Records and introduced in 1948. The short-playing but convenient 7-inch 45 rpm microgroove vinyl "single was introduced by "RCA Victor in 1949. In the US and most developed countries, the two new vinyl formats completely replaced 78 rpm shellac discs by the end of the 1950s, but in some corners of the world, the "78" lingered on far into the 1960s. Vinyl was much more expensive than shellac, one of the several factors that made its use for 78 rpm records very unusual, but with a long-playing disc the added cost was acceptable and the compact "45" format required very little material. Vinyl offered improved performance, both in stamping and in playback. If played with a good diamond stylus mounted in a lightweight pickup on a well-adjusted tonearm, it was long-lasting. If protected from dust, scuffs and scratches there was very little noise. Vinyl records were, over-optimistically, advertised as "unbreakable". They were not, but they were much less fragile than shellac, which had itself once been touted as "unbreakable" compared to wax cylinders.
Between the invention of the phonograph in 1877 and the first commercial "digital recordings in the early 1970s, arguably the most important milestone in the history of sound recording was the introduction of what was then called electrical recording, in which a "microphone was used to convert the sound into an electrical signal that was amplified and used to actuate the recording stylus. This innovation eliminated the "horn sound" resonances characteristic of the acoustical process, produced clearer and more full-bodied recordings by greatly extending the useful range of audio frequencies, and allowed previously unrecordable distant and feeble sounds to be captured.
Sound recording began as a purely mechanical process. Except for a few crude telephone-based recording devices with no means of amplification, such as the "Telegraphone, it remained so until the 1920s when several radio-related developments in "electronics converged to revolutionize the recording process. These included improved microphones and auxiliary devices such as electronic filters, all dependent on electronic "amplification to be of practical use in recording. In 1906, "Lee De Forest invented the "Audion "triode vacuum tube, an electronic valve that could amplify weak electrical signals. By 1915, it was in use in long-distance telephone circuits that made conversations between New York and San Francisco practical. Refined versions of this tube were the basis of all electronic sound systems until the commercial introduction of the first "transistor-based audio devices in the mid-1950s.
During World War I, engineers in the United States and Great Britain worked on ways to record and reproduce, among other things, the sound of a "German U-boat for training purposes. Acoustical recording methods of the time could not reproduce the sounds accurately. The earliest results were not promising.
The first electrical recording issued to the public, with little fanfare, was of November 11, 1920 funeral services for "The Unknown Warrior in "Westminster Abbey, London. The recording engineers used microphones of the type used in contemporary telephones. Four were discreetly set up in the abbey and wired to recording equipment in a vehicle outside. Although electronic amplification was used, the audio was weak and unclear. The procedure did, however, produce a recording that would otherwise not have been possible in those circumstances. For several years, this little-noted disc remained the only issued electrical recording.
Several record companies and independent inventors, notably "Orlando Marsh, experimented with equipment and techniques for electrical recording in the early 1920s. Marsh's electrically recorded "Autograph Records were already being sold to the public in 1924, a year before the first such offerings from the major record companies, but their overall sound quality was too low to demonstrate any obvious advantage over traditional acoustical methods. Marsh's microphone technique was idiosyncratic and his work had little if any impact on the systems being developed by others.
Telephone industry giant "Western Electric had research laboratories (merged with the "AT&T engineering department in 1925 to form "Bell Telephone Laboratories) with material and human resources that no record company or independent inventor could match. They had the best microphone, a condenser type developed there in 1916 and greatly improved in 1922, and the best amplifiers and test equipment. They had already patented an electromechanical recorder in 1918, and in the early 1920s, they decided to intensively apply their hardware and expertise to developing two state-of-the-art systems for electronically recording and reproducing sound: one that employed conventional discs and another that recorded optically on motion picture film. Their engineers pioneered the use of mechanical analogs of electrical circuits and developed a superior "rubber line" recorder for cutting the groove into the wax master in the disc recording system.
By 1924, such dramatic progress had been made that Western Electric arranged a demonstration for the two leading record companies, the "Victor Talking Machine Company and the "Columbia Phonograph Company. Both soon licensed the system and both made their earliest published electrical recordings in February 1925, but neither actually released them until several months later. To avoid making their existing catalogs instantly obsolete, the two long-time archrivals agreed privately not to publicize the new process until November 1925, by which time enough electrically recorded repertory would be available to meet the anticipated demand. During the next few years, the lesser record companies licensed or developed other electrical recording systems. By 1929 only the budget label "Harmony was still issuing new recordings made by the old acoustical process.
Comparison of some surviving Western Electric test recordings with early commercial releases indicates that the record companies "dumbed down" the frequency range of the system so the recordings would not overwhelm non-electronic playback equipment, which reproduced very low frequencies as an unpleasant rattle and rapidly wore out discs with strongly recorded high frequencies.["citation needed]
In the 1920s, "Phonofilm and other early motion picture sound systems employed "optical recording technology, in which the audio signal was graphically recorded on photographic film. The amplitude variations comprising the signal were used to modulate a light source which was imaged onto the moving film through a narrow slit, allowing the signal to be photographed as variations in the density or width of a "sound track". The "projector used a steady light and a "photoelectric cell to convert these variations back into an electrical signal, which was amplified and sent to "loudspeakers behind the screen. Ironically, the introduction of ""talkies" was spearheaded by "The Jazz Singer (1927), which used the "Vitaphone "sound-on-disc system rather than an optical soundtrack. Optical sound became the standard motion picture audio system throughout the world and remains so for theatrical release prints despite attempts in the 1950s to substitute magnetic soundtracks. Currently, all release prints on "35 mm film include an analog optical soundtrack, usually stereo with "Dolby SR noise reduction. In addition, an optically recorded digital soundtrack in Dolby Digital and/or Sony SDDS form is likely to be present. An optically recorded timecode is also commonly included to synchronise CDROMs that contain a DTS soundtrack.
This period also saw several other historic developments including the introduction of the first practical magnetic sound recording system, the "magnetic wire recorder, which was based on the work of Danish inventor "Valdemar Poulsen. Magnetic wire recorders were effective, but the sound quality was poor, so between the wars, they were primarily used for voice recording and marketed as business dictating machines. In 1924, a German engineer, Dr. Kurt Stille, developed the Poulsen wire recorder as a dictating machine. The following year, "Ludwig Blattner began work that eventually produced the Blattnerphone, enhancing it to use steel tape instead of wire. The "BBC started using Blattnerphones in 1930 to record radio programmes. In 1933, radio pioneer "Guglielmo Marconi's company purchased the rights to the Blattnerphone, and newly developed Marconi-Stille recorders were installed in the BBC's "Maida Vale Studios in March 1935. The tape used in Blattnerphones and Marconi-Stille recorders was the same material used to make razor blades, and not surprisingly the fearsome Marconi-Stille recorders were considered so dangerous that technicians had to operate them from another room for safety. Because of the high recording speeds required, they used enormous reels about one metre in diameter, and the thin tape frequently broke, sending jagged lengths of razor steel flying around the studio. The K1 "Magnetophon was the first practical tape recorder, developed by AEG in Germany in 1935.
An important field of invention during this period was the "tape recorder. "Magnetic tape recording uses an amplified electrical audio signal to generate analogous variations of the magnetic field produced by a "tape head, which impresses corresponding variations of magnetization on the moving tape. In playback mode, the signal path is reversed, the tape head acting as a miniature "electric generator as the varyingly magnetized tape passes over it. The original solid steel ribbon was replaced by a much more practical coated paper tape, but acetate soon replaced paper as the standard tape base. Acetate has fairly low tensile strength and if very thin it will snap easily, so it was in turn eventually superseded by polyester. This technology, the basis for almost all commercial recording from the 1950s to the 1980s, was developed in the 1930s by German audio engineers who also rediscovered the principle of "AC biasing (first used in the 1920s for "wire recorders), which dramatically improved the frequency response of tape recordings. The technology was further improved just after World War II by American audio engineer "John T. Mullin with backing from "Bing Crosby Enterprises. Mullin's pioneering recorders were modifications of captured German recorders. In the late 1940s, the "Ampex company produced the first tape recorders commercially available in the US.
Magnetic tape brought about sweeping changes in both radio and the recording industry. Sound could be recorded, erased and re-recorded on the same tape many times, sounds could be duplicated from tape to tape with only minor loss of quality, and recordings could now be very precisely edited by physically cutting the tape and rejoining it. Within a few years of the introduction of the first commercial tape recorder—the Ampex 200 model, launched in 1948—American musician-inventor "Les Paul had invented the first "multitrack tape recorder, ushering in another technical revolution in the recording industry. Tape made possible the first sound recordings totally created by electronic means, opening the way for the bold sonic experiments of the "Musique Concrète school and avant garde composers like "Karlheinz Stockhausen, which in turn led to the innovative pop music recordings of artists such as "Frank Zappa, "The Beatles, and "The Beach Boys.
The ease and accuracy of tape editing, as compared to the cumbersome disc-to-disc editing procedures previously in some limited use, together with tape's consistently high audio quality finally convinced radio networks to routinely prerecord their entertainment programming, most of which had formerly been broadcast live. Also, for the first time, broadcasters, regulators and other interested parties were able to undertake comprehensive audio logging of each day's radio broadcasts. Innovations like multitracking and "tape echo allowed radio programs and advertisements to be produced to a high level of complexity and sophistication. The combined impact with innovations such as the endless loop "broadcast cartridge led to significant changes in the pacing and production style of radio program content and advertising.
In 1881, it was noted during experiments in transmitting sound from the Paris Opera that it was possible to follow the movement of singers on the stage if earpieces connected to different microphones were held to the two ears. This discovery was commercialized in 1890 with the "Théâtrophone system, which operated for over forty years until 1932. In 1931, "Alan Blumlein, a British electronics engineer working for "EMI, designed a way to make the sound of an actor in a film follow his movement across the screen. In December 1931, he submitted a patent including the idea, and in 1933 this became UK patent number 394,325. Over the next two years, Blumlein developed stereo microphones and a stereo disc-cutting head, and recorded a number of short films with stereo soundtracks.
In the 1930s, experiments with magnetic tape enabled the development of the first practical commercial sound systems that could record and reproduce high-fidelity "stereophonic sound. The experiments with stereo during the 1930s and 1940s were hampered by problems with synchronization. A major breakthrough in practical stereo sound was made by "Bell Laboratories, who in 1937 demonstrated a practical system of two-channel stereo, using dual optical sound tracks on film. Major movie studios quickly developed three-track and four-track sound systems, and the first stereo sound recording for a commercial film was made by "Judy Garland for the "MGM movie "Listen, Darling in 1938. The first commercially released movie with a stereo soundtrack was Walt Disney's "Fantasia, released in 1940. The 1941 release of Fantasia used the ""Fantasound" sound system. This system used a separate film for the sound, synchronized with the film carrying the picture. The sound film had four double-width optical soundtracks, three for left, center, and right audio—and a fourth as a "control" track with three recorded tones that controlled the playback volume of the three audio channels. Because of the complex equipment this system required, Disney exhibited the movie as a roadshow, and only in the United States. Regular releases of the movie used standard mono optical 35 mm stock until 1956, when Disney released the film with a stereo soundtrack that used the ""Cinemascope" four-track magnetic sound system.
German audio engineers working on magnetic tape developed stereo recording by 1941, even though a 2-track push-pull monaural technique existed in 1939. Of 250 stereophonic recordings made during WW2, only three survive: Beethoven's 5th Piano Concerto with Walter Gieseking and Arthur Rother, a Brahms Serenade, and the last movement of Bruckner's 8th Symphony with Von Karajan. The "Audio Engineering Society has issued all these recordings on "CD. ("Varese Sarabande had released the Beethoven Concerto on LP, and it has been reissued on CD several times since). Other early German stereophonic tapes are believed to have been destroyed in bombings. Not until "Ampex introduced the first commercial two-track tape recorders in the late 1940s did stereo tape recording become commercially feasible. However, despite the availability of multitrack tape, stereo did not become the standard system for commercial music recording for some years, and remained a specialist market during the 1950s. EMI (UK) was the first company to release commercial stereophonic tapes. They issued their first Stereosonic tape in 1954. Others quickly followed, under the His Master's Voice and Columbia labels. 161 Stereosonic tapes were released, mostly classical music or lyric recordings. RCA imported these tapes into the USA.
Two-track stereophonic tapes were more successful in America during the second half of the 1950s. They were duplicated at real time (1:1) or at twice the normal speed (2:1) when later 4-track tapes were often duplicated at up to 16 times the normal speed, providing a lower sound quality in many cases. Early American 2-track stereophonic tapes were very expensive. A typical example is the price list of the Sonotape/Westminster reels: $6.95, $11.95 and $17.95 for the 7000, 9000 and 8000 series respectively. Some HMV tapes released in the USA also cost up to $15. The history of stereo recording changed after the late 1957 introduction of the Westrex stereo phonograph disc, which used the groove format developed earlier by Blumlein. "Decca Records in England came out with "FFRR (Full Frequency Range Recording) in the 1940s, which became internationally accepted as a worldwide standard for higher quality recording on vinyl records. The "Ernest Ansermet recording of "Igor Stravinsky's "Petrushka was key in the development of full frequency range records and alerting the listening public to high fidelity in 1946.
Record companies mixed most popular music singles into monophonic sound until the mid-1960s—then commonly released major recordings in both mono and stereo until the early 1970s. Many 1960s pop albums available only in stereo in the 2000s were originally released only in mono, and record companies produced the "stereo" versions of these albums by simply separating the two tracks of the master tape, creating "pseudo stereo". In the mid Sixties, as stereo became more popular, many mono recordings (such as The Beach Boys' "Pet Sounds) were remastered using the so-called ""fake stereo" method, which spread the sound across the stereo field by directing higher-frequency sound into one channel and lower-frequency sounds into the other.
This section does not "cite any "sources. (December 2008) ("Learn how and when to remove this template message)
Magnetic tape transformed the recording industry. By the early 1950s, most commercial recordings were mastered on tape instead of recorded directly to disc. Tape facilitated a degree of manipulation in the recording process that was impractical with mixes and multiple generations of directly recorded discs. An early example is "Les Paul's 1951 recording of "How High the Moon, on which Paul played eight overdubbed guitar tracks. In the 1960s "Brian Wilson of "The Beach Boys, "Frank Zappa, and "The Beatles (with producer "George Martin) were among the first popular artists to explore the possibilities of "multitrack recording techniques and effects on their landmark albums "Pet Sounds, "Freak Out!, and "Sgt. Pepper's Lonely Hearts Club Band.
The next important innovation was small cartridge-based tape systems, of which the "compact cassette, commercialized by the "Philips electronics company in 1964, is the best known. Initially a low-fidelity format for spoken-word voice recording and inadequate for music reproduction, after a series of improvements it entirely replaced the competing formats: the larger "8-track tape (used primarily in cars) and the fairly similar "Deutsche Cassette" developed by the German company Grundig. This latter system was not particularly common in Europe and practically unheard-of in America. The compact cassette became a major consumer audio format and advances in electronic and mechanical miniaturization led to the development of the "Sony "Walkman, a pocket-sized cassette player introduced in 1979. The Walkman was the first personal music player and it gave a major boost to sales of prerecorded cassettes, which became the first widely successful release format that used a re-recordable medium: the vinyl record was a playback-only medium and commercially prerecorded tapes for "reel-to-reel tape decks, which many consumers found difficult to operate, were never more than an uncommon niche market item.
A key advance in audio fidelity came with the "Dolby A noise reduction system, invented by "Ray Dolby and introduced into professional recording studios in 1966. It suppressed the light but sometimes quite noticeable steady background of hiss, which was the only easily audible downside of mastering on tape instead of recording directly to disc. A competing system, "dbx, invented by David Blackmer, also found success in professional audio. A simpler variant of Dolby's noise reduction system, known as Dolby B, greatly improved the sound of cassette tape recordings by reducing the especially high level of hiss that resulted from the cassette's miniaturized tape format. It, and variants, also eventually found wide application in the recording and film industries. Dolby B was crucial to the popularization and commercial success of the cassette as a domestic recording and playback medium, and it became a standard feature in the booming home and car stereo market of the 1970s and beyond. The compact cassette format also benefited enormously from improvements to the tape itself as coatings with wider frequency responses and lower inherent noise were developed, often based on cobalt and chrome oxides as the magnetic material instead of the more usual iron oxide.
The multitrack audio cartridge had been in wide use in the radio industry, from the late 1950s to the 1980s, but in the 1960s the pre-recorded "8-track cartridge was launched as a consumer audio format by "Bill Lear of the Lear Jet aircraft company (and although its correct name was the 'Lear Jet Cartridge', it was seldom referred to as such). Aimed particularly at the automotive market, they were the first practical, affordable car hi-fi systems, and could produce sound quality superior to that of the compact cassette. However the smaller size and greater durability — augmented by the ability to create home-recorded music "compilations" since 8-track recorders were rare — saw the cassette become the dominant consumer format for portable audio devices in the 1970s and 1980s.
There had been experiments with multi-channel sound for many years — usually for special musical or cultural events — but the first commercial application of the concept came in the early 1970s with the introduction of "Quadraphonic sound. This spin-off development from multitrack recording used four tracks (instead of the two used in stereo) and four speakers to create a 360-degree audio field around the listener. Following the release of the first consumer 4-channel "hi-fi systems, a number of popular albums were released in one of the competing four-channel formats; among the best known are "Mike Oldfield's "Tubular Bells and "Pink Floyd's "The Dark Side of the Moon. Quadraphonic sound was not a commercial success, partly because of competing and somewhat incompatible four-channel sound systems (e.g., "CBS, "JVC, "Dynaco and others all had systems) and generally poor quality, even when played as intended on the correct equipment, of the released music. It eventually faded out in the late 1970s, although this early venture paved the way for the eventual introduction of domestic "Surround Sound systems in home theatre use, which have gained enormous popularity since the introduction of the DVD. This widespread adoption has occurred despite the confusion introduced by the multitude of available surround sound standards.
The replacement of the relatively fragile thermionic valve ("vacuum tube) by the smaller, lighter-weight, cooler-running, less expensive, more robust, and less power-hungry "transistor also accelerated the sale of consumer high-fidelity ""hi-fi" sound systems from the 1960s onward. In the 1950s, most record players were monophonic and had relatively low sound quality. Few consumers could afford high-quality stereophonic sound systems. In the 1960s, American manufacturers introduced a new generation of "modular" hi-fi components — separate turntables, pre-amplifiers, amplifiers, both combined as integrated amplifiers, tape recorders, and other ancillary equipment like the "graphic equaliser, which could be connected together to create a complete home sound system. These developments were rapidly taken up by major Japanese electronics companies, which soon flooded the world market with relatively affordable, high-quality transistorized audio components. By the 1980s, corporations like "Sony had become world leaders in the music recording and playback industry.
The advent of "digital sound recording and later the "compact disc (CD) in 1982 brought significant improvements in the durability of consumer recordings. The CD initiated another massive wave of change in the consumer music industry, with "vinyl records effectively relegated to a small niche market by the mid-1990s. However, the record industry fiercely resisted the introduction of digital systems, fearing wholesale piracy on a medium able to produce perfect copies of original released recordings. However, the industry succumbed to the inevitable, though using various protection system (principally "Serial Copy Management System, or SCMS).
The most recent and revolutionary developments have been in digital recording, with the development of various uncompressed and compressed digital "audio file formats, "processors capable and fast enough to convert the digital data to sound in "real time, and inexpensive "mass storage. This generated new types of "portable digital audio players. The "minidisc player, using "ATRAC compression on small, cheap, re-writeable discs was introduced in the 1990s but became obsolescent as solid-state non-volatile "flash memory dropped in price. As technologies that increase the amount of data that can be stored on a single medium, such as "Super Audio CD, "DVD-A, "Blu-ray Disc, and "HD DVD become available, longer programs of higher quality fit onto a single disc. Sound files are readily "downloaded from the Internet and other sources, and copied onto computers and digital audio players. Digital audio technology is now used in all areas of audio, from casual use of music files of moderate quality to the most demanding professional applications. New applications such as "internet radio and "podcasting have appeared.
Technological developments in recording, editing, and consuming have transformed the "record, "movie and "television industries in recent decades. "Audio editing became practicable with the invention of "magnetic tape recording, but digital audio and cheap "mass storage allows computers to edit audio files quickly, easily, and cheaply. Today, the process of making a recording is separated into tracking, "mixing and "mastering. "Multitrack recording makes it possible to capture signals from several microphones, or from different "takes to tape, disc or mass storage, with maximized "headroom and quality, allowing previously unavailable flexibility in the mixing and mastering stages.
There are many different digital audio recording and processing programs running under several computer "operating systems for all purposes, ranging from casual users (e.g., a "small business person recording her "to-do" list on an inexpensive digital recorder) to serious amateurs (an unsigned "indie" band recording their demo on a laptop) to professional "sound engineers who are recording albums, film scores and doing sound design for "video games. A comprehensive list of digital recording applications is available at the "digital audio workstation article. "Digital dictation software for recording and transcribing speech has different requirements; intelligibility and flexible playback facilities are priorities, while a wide frequency range and high audio quality are not.
This section does not "cite any "sources. (April 2017) ("Learn how and when to remove this template message)
The development of analog sound recording in the nineteenth century and its widespread use throughout the twentieth century had a huge impact on the development of music. Before analog sound recording was invented, most music was listened to by hearing a live performance, or by singing or playing a song or piece. Throughout the "medieval, "Renaissance, "Baroque, "Classical, and through much of the "Romantic music era, the main way that songs and instrumental pieces were "recorded" was by notating the piece in "music notation. While music notation indicates the pitches of the melody and their rhythm, the notation is not like a 2010-era sound recording. Indeed, in the Medieval era, "Gregorian chant did not indicate the rhythm of the chant. In the Baroque era, instrumental pieces often lack a tempo indication and usually none of the ornaments were written down. As a result, each performance of a song or piece would be slightly different.
With the development of analog sound recording, though, a performance could be permanently fixed, in all of its elements: pitch, rhythm, timbre, ornaments and expression. This meant that many more elements of a performance would be captured and disseminated to other listeners. The development of sound recording also enabled a much larger proportion of people to hear famous orchestras, operas, singers and bands, because even if a non-wealthy person could not afford to hear the live concert, she or he might be able to afford to buy the recording. The availability of sound recording thus helped to spread musical styles to new regions, countries and continents. The cultural influence went in a number of directions. Sound recordings enabled Western music lovers to hear actual recordings of Asian, Middle Eastern and African groups and performers, increasing awareness of non-Western musical styles. At the same time, sound recordings enabled non-Western music lovers to hear the most famous North American and European groups and singers.
Since 1934, copyright law has treated sound recordings (or phonograms) differently from "musical works. "Copyright, Designs and Patents Act 1988 defines a sound recording as (a) a recording of sounds, from which the sounds may be reproduced, or (b) a recording of the whole or any part of a literary, dramatic or musical work, from which sounds reproducing the work or part may be produced, regardless of the medium on which the recording is made or the method by which the sounds are reproduced or produced. It thus covers vinyl records, tapes, "compact discs, digital audiotapes, and MP3s that embody recordings.
|Wikiquote has quotations related to: recording|