Statistical process control (SPC) is a method of "quality control which employs "statistical methods to monitor and control a process. This helps ensure the process operates efficiently, producing more specification-conforming product with less waste (rework or "scrap). SPC can be applied to any process where the "conforming product" (product meeting specifications) output can be measured. Key tools used in SPC include "run charts, "control charts, a focus on "continuous improvement, and "the design of experiments. An example of a process where SPC is applied is manufacturing lines.
SPC must be practiced in 2 phases: The first phase is the initial establishment of the process, and the second phase is the regular production use of the process. In the second phase, a decision of the period to be examined must be made, depending upon the change in 5M&E conditions (Man, Machine, Material, Method, Movement, Environment) and wear rate of parts used in the manufacturing process (machine parts, jigs, and fixtures).
An advantage of SPC over other methods of quality control, such as "inspection", is that it emphasizes early detection and prevention of problems, rather than the correction of problems after they have occurred.
In addition to reducing waste, SPC can lead to a reduction in the time required to produce the product. SPC makes it less likely the finished product will need to be reworked or scrapped.
SPC was pioneered by "Walter A. Shewhart at "Bell Laboratories in the early 1920s. Shewhart developed the control chart in 1924 and the concept of a state of statistical control. Statistical control is equivalent to the concept of "exchangeability developed by logician "William Ernest Johnson also in 1924 in his book Logic, Part III: The Logical Foundations of Science. Along with a team at AT&T that included Harold Dodge and Harry Romig he worked to put "sampling inspection on a rational statistical basis as well. Shewhart consulted with Colonel Leslie E. Simon in the application of control charts to munitions manufacture at the Army's "Picatinny Arsenal in 1934. That successful application helped convince Army Ordnance to engage AT&T's George Edwards to consult on the use of statistical quality control among its divisions and contractors at the outbreak of World War II.
"W. Edwards Deming invited Shewhart to speak at the Graduate School of the U.S. Department of Agriculture, and served as the editor of Shewhart's book Statistical Method from the Viewpoint of Quality Control (1939) which was the result of that lecture. Deming was an important architect of the quality control short courses that trained American industry in the new techniques during WWII. The graduates of these wartime courses formed a new professional society in 1945, the American Society for Quality Control, which elected Edwards as its first president. Deming traveled to Japan during the Allied Occupation and met with the Union of Japanese Scientists and Engineers (JUSE) in an effort to introduce SPC methods to "Japanese industry .
Shewhart read the new statistical theories coming out of Britain, especially the work of "William Sealy Gosset, "Karl Pearson, and "Ronald Fisher. However, he understood that data from physical processes seldom produced a ""normal distribution curve"; that is, a "Gaussian distribution or ""bell curve". He discovered that data from measurements of variation in manufacturing did not always behave the way as data from measurements of natural phenomena (for example, "Brownian motion of particles). Shewhart concluded that while every process displays variation, some processes display variation that is natural to the process ("common" sources of variation)- these processes were described as 'in (statistical) control'. Other processes additionally display variation that is not present in the causal system of the process at all times ("special" sources of variation), and these were described as 'not in control'.
In 1988, the "Software Engineering Institute suggested that SPC could be applied to non-manufacturing processes, such as software engineering processes, in the "Capability Maturity Model (CMM). The Level 4 and Level 5 practices of the Capability Maturity Model Integration ("CMMI) use this concept.
The notion that SPC is a useful tool when applied to non-repetitive, knowledge-intensive processes such as research and development or systems engineering has encountered skepticism and remains controversial.
In his seminal article No Silver Bullet, "Fred Brooks points out that the complexity, conformance requirements, changeability, and invisibility of software results in inherent and essential variation that cannot be removed. This implies that SPC is less effective in the domain of software development than in, e.g., manufacturing.
In manufacturing, quality is defined as conformance to specification. However, no two products or characteristics are ever exactly the same, because any process contains many sources of variability. In mass-manufacturing, traditionally, the quality of a finished article is ensured by post-manufacturing inspection of the product. Each article (or a sample of articles from a production lot) may be accepted or rejected according to how well it meets its design "specifications. In contrast, SPC uses "statistical tools to observe the performance of the production process in order to detect significant variations before they result in the production of a sub-standard article. Any source of variation at any point of time in a process will fall into one of two classes.
Most processes have many sources of variation; most of them are minor and may be ignored. If the dominant sources of variation are identified, however, resources for change can be focused on them. If the dominant assignable sources of variation are detected, potentially they can be identified and removed. Once removed, the process is said to be "stable". When a process is stable, its variation should remain within a known set of limits. That is, at least, until another assignable source of variation occurs. For example, a breakfast cereal packaging line may be designed to fill each cereal box with 500 grams of cereal. Some boxes will have slightly more than 500 grams, and some will have slightly less. When the package weights are measured, the data will demonstrate a "distribution of net weights. If the production process, its inputs, or its environment (for example, the machines on the line) change, the distribution of the data will change. For example, as the cams and pulleys of the machinery wear, the cereal filling machine may put more than the specified amount of cereal into each box. Although this might benefit the customer, from the manufacturer's point of view, this is wasteful and increases the cost of production. If the manufacturer finds the change and its source in a timely manner, the change can be corrected (for example, the cams and pulleys replaced).
The application of SPC involves three main phases of activity:
The data from measurements of variations at points on the process map is monitored using "control charts. Control charts attempt to differentiate "assignable" ("special") sources of variation from "common" sources. "Common" sources, because they are an expected part of the process, are of much less concern to the manufacturer than "assignable" sources. Using control charts is a continuous activity, ongoing over time.
When the process does not trigger any of the control chart "detection rules" for the control chart, it is said to be "stable". A "process capability analysis may be performed on a stable process to predict the ability of the process to produce "conforming product" in the future.
When the process triggers any of the control chart "detection rules", (or alternatively, the process capability is low), other activities may be performed to identify the source of the excessive variation. The tools used in these extra activities include: "Ishikawa diagram, "designed experiments, and "Pareto charts. Designed experiments are a means of objectively quantifying the relative importance (strength) of sources of variation. Once the sources of (special cause) variation are identified, they can be minimized or eliminated. Steps to eliminating a source of variation might include: development of standards, staff training, error-proofing, and changes to the process itself or its inputs.
When monitoring many processes with control charts, it is sometimes useful to calculate quantitative measures of the stability of the processes. These metrics can then be used to identify/prioritize the processes that are most in need of corrective actions. These metrics can also be viewed as supplementing the traditional "process capability metrics. Several metrics have been proposed, as described in Ramirez and Runger.  They are (1) a Stability Ratio which compares the long-term variability to the short-term variability, (2) an ANOVA Test which compares the within-subgroup variation to the between-subgroup variation, and (3) an Instability Ratio which compares the number of subgroups that have one or more violations of the "Western Electric rules to the total number of subgroups.
Digital control charts use logic-based rules that determine "derived values" which signal the need for correction. For example,
This article includes a "list of references, but its sources remain unclear because it has insufficient "inline citations. (July 2014) ("Learn how and when to remove this template message)
|Wikimedia Commons has media related to Statistical process control.|