See more Stereo microscope articles on AOD.

Powered by
Share this page on
Article provided by Wikipedia

( => ( => ( => Stereo microscope [pageid] => 19202502 ) =>
Stereo microscope
Modern stereomicroscope optical design.
A - Objective B - Galilean telescopes (rotating objectives) C - Zoom control D - Internal objective E - Prism F - Relay lens G - Reticle H - Eyepiece

The stereo or stereoscopic or dissecting microscope is an "optical microscope variant designed for low magnification observation of a sample, typically using light reflected from the surface of an object rather than transmitted through it. The instrument uses two separate optical paths with two objectives and eyepieces to provide slightly different viewing angles to the left and right eyes. This arrangement produces a "three-dimensional visualization of the sample being examined.[1] Stereomicroscopy overlaps "macrophotography for recording and examining solid samples with complex surface "topography, where a three-dimensional view is needed for analyzing the detail.

The stereo microscope is often used to study the surfaces of solid specimens or to carry out close work such as "dissection, "microsurgery, "watch-making, "circuit board manufacture or inspection, and "fracture surfaces as in "fractography and "forensic engineering. They are thus widely used in "manufacturing industry for "manufacture, "inspection and "quality control. Stereo microscopes are essential tools in entomology.

The stereo microscope should not be confused with a "compound microscope equipped with double eyepieces and a "binoviewer. In such a microscope, both eyes see the same image, with the two eyepieces serving to provide greater viewing comfort. However, the image in such a microscope is no different from that obtained with a single monocular eyepiece.


Differences to normal optical microscopes[edit]

Unlike a compound "light microscope, illumination in a stereo microscope most often uses "reflected illumination rather than "transmitted (diascopic) illumination, that is, light reflected from the surface of an object rather than light transmitted through an object. Use of reflected light from the object allows examination of specimens that would be too thick or otherwise opaque for compound microscopy. Some stereo microscopes are also capable of transmitted light illumination as well, typically by having a bulb or mirror beneath a transparent stage underneath the object, though unlike a compound microscope, transmitted illumination is not focused through a condenser in most systems.[2] Stereoscopes with specially-equipped illuminators can be used for "dark field microscopy, using either reflected or transmitted light.[3]

"Scientist using a stereo microscope outfitted with a digital imaging pick-up and "fibre-optic illumination

Great working distance and depth of field are important qualities for this type of microscope. Both qualities are inversely correlated with resolution: the higher the resolution (i.e. the greater the distance at which two adjacent points can be distinguished as separate), the smaller the depth of field and working distance. Some stereo microscopes can deliver a useful magnification up to 100×, comparable to a 10× objective and 10× eyepiece in a normal compound microscope, although the magnification is often much lower. This is around one tenth the useful resolution of a normal compound optical microscope.

The large working distance at low magnification is useful in examining large solid objects such as fracture surfaces, especially using "fibre-optic illumination. Such samples can also be manipulated easily so as to determine the points of interest. There are severe limitations on sample size in "scanning electron microscopy, as well as ease of manipulation in the specimen chamber.


There are two major types of magnification systems in stereo microscopes. One type is fixed magnification in which primary magnification is achieved by a paired set of "objective lenses with a set degree of magnification. The other is zoom or pancreatic magnification, which are capable of a continuously variable degree of magnification across a set range. Zoom systems can achieve further magnification through the use of auxiliary objectives that increase total magnification by a set factor. Also, total magnification in both fixed and zoom systems can be varied by changing eyepieces.[1]

Intermediate between fixed magnification and zoom magnification systems is a system attributed to "Galileo as the ""Galilean optical system" ; here an arrangement of fixed-focus convex lenses is used to provide a fixed magnification, but with the crucial distinction that the same optical components in the same spacing will, if physically inverted, result in a different, though still fixed, magnification. This allows one set of lenses to provide two different magnifications ; two sets of lenses to provide four magnifications on one turret ; three sets of lenses provide six magnifications and will still fit into one turret. Practical experience shows that such "Galilean optics systems are as useful as a considerably more expensive zoom system, with the advantage of knowing the magnification in use as a set value without having to read analogue scales. (In remote locations, the robustness of the systems is also a non-trivial advantage.)


Small specimens necessarily require intense illumination, especially at high magnifications, and this is usually provided by a "fibre-optic light source. Fiber optics utilize "halogen lamps which provide high light output for a given power input. The lamps are small enough to be fitted easily near the microscope, although they often need cooling to ameliorate high temperatures from the bulb. The fibre-optic stalk gives the operator much freedom in choosing appropriate lighting conditions for the sample. The stalk is encased in a sheath that is easy to move and manipulate to any desired position. The stalk is normally unobtrusive when the lit end is near the specimen, so usually does not interfere with the image in the microscope. Examination of "fracture surfaces frequently need oblique lighting so as to highlight surface features during "fractography, and fibre-optic lights are ideal for this purpose. Several such light stalks can be used for the same specimen, so increasing the illumination yet further.

More recent developments in the lighting for dissecting microscopes include the use of "high-power LEDs which are much more energy efficient than halogens and are able to produce a spectrum of colors of light, making them useful for "fluorophore analysis of biological samples (impossible with a halogen or mercury vapor light source).

Digital display[edit]

Labomed LB-343 5.0 MP digital stereo microscope with 9 inch HD LCD screen, HDMI video output, X/Y digital micrometer and moving stage

Video cameras are integrated into some stereo microscopes, allowing the magnified images to be displayed on a high resolution monitor. The large display helps to reduce the eye fatigue that would result from using a conventional microscope for extended periods.

In some units, a built-in computer converts the images from two cameras (one per eyepiece) to a 3D "anaglyph image for viewing with red/cyan glasses, or to the cross converged process["clarify] for clear glasses and improved color accuracy. The results are viewable by a group wearing the glasses. More typically, a 2D image is displayed from a single camera attached to one of the eyepieces.

See also[edit]


  1. ^ a b "Introduction to Stereomicroscopy" by Paul E. Nothnagle, William Chambers, and "Michael W. Davidson, "Nikon MicroscopyU.
  2. ^ "Illumination for Stereomicroscopy: Reflected (Episcopic) Light" by Paul E. Nothnagle, William Chambers, Thomas J. Fellers, and Michael W. Davidson , Nikon MicroscopyU.
  3. ^ "Illumination for Stereomicroscopy: Darkfield Illumination" by William Chambers, Thomas J. Fellers, and Michael W. Davidson , Nikon MicroscopyU.
) )